home *** CD-ROM | disk | FTP | other *** search
/ Night Owl 9 / Night Owl CD-ROM (NOPV9) (Night Owl Publisher) (1993).ISO / 015a / msd6txt.zip / NETWORKS.TXT next >
Text File  |  1993-03-10  |  23KB  |  639 lines

  1.  
  2. NETWORKS.TXT
  3.  
  4. This file contains information about making your network
  5. compatible with MS-DOS 6. If you are running MS-DOS 5.0, you
  6. do not need to make any changes to your network to make it
  7. compatible with MS-DOS 6. 
  8.  
  9. If Setup referred you to this file, see Section 1 below. 
  10. If you are looking for additional information about
  11. your network software, find the appropriate section
  12. below.
  13.  
  14. This file contains the following sections:
  15.  
  16. 1.  Setup referred you to the NETWORKS.TXT file
  17. 2.  DoubleSpace and Network Drivers
  18. 3.  MS-DOS Shell and Networks
  19. 4.  3+Share
  20. 5.  Arcnet systems
  21. 6.  Artisoft LANtastic
  22. 7.  AT&T StarGroup (non-LAN Manager) 
  23. 8.  Banyan VINES
  24. 9.  DEC Pathworks and PCSA
  25. 10. IBM PC LAN
  26. 11. IBM DOS LAN Requester Version 1.30 or Earlier
  27. 12. Microsoft LAN Manager and 100-Percent Compatible
  28.     Networks
  29. 13. Microsoft MS-Net and 100-Percent Compatible
  30.     Networks
  31. 14. Net/One PC  
  32. 15. Novell Networks
  33. 16. Novell Networks and DoubleSpace
  34. 17. PC-NFS
  35. 18. TCS 10Net or DCA 10Net
  36.  
  37. 1.  Setup referred you to the NETWORKS.TXT file
  38. ===============================================
  39. If Setup displayed the "You have specified that your
  40. computer is connected to a network" screen, your computer
  41. might be running an older version of network software
  42. that is incompatible with MS-DOS 6. For more information,
  43. see the section in this file that addresses your network 
  44. software. If you don't find instructions on making 
  45. your network compatible with MS-DOS 6, obtain an upgrade 
  46. of your network software from your network vendor, install 
  47. the upgraded network files, and then run MS-DOS 6 Setup again. 
  48.  
  49. After you have upgraded your network software, when Setup displays 
  50. the "You have specified that your computer is connected to a network" 
  51. screen, choose the Continue option. Your network should work correctly 
  52. with MS-DOS 6.
  53.  
  54. 2. DoubleSpace and Network Drivers
  55. ==================================
  56. If you have any problems running your network software on a DoubleSpace
  57. drive, make sure that the command that loads your DBLSPACE.SYS file 
  58. appears in your CONFIG.SYS file before any commands that load your 
  59. network drivers.
  60.  
  61. For problems with specific network software and DoubleSpace, refer
  62. to the section below pertains to your network sofware.
  63.  
  64. 3. MS-DOS Shell and Networks
  65. ============================
  66. Most network software won't work correctly if you start it
  67. from a command prompt in MS-DOS Shell. Start your network
  68. before starting MS-DOS Shell.
  69.  
  70. 4. 3+Share
  71. ==========
  72. If your network software is 3+Share 1.6 or earlier, and you previously
  73. upgaded to MS-DOS 5.0, your current version of the 3+Share redirector
  74. will work with MS-DOS 6. After you install MS-DOS 6, type the
  75. following at the command prompt, and restart your computer:
  76.  
  77.    SETVER MSREDIR.EXE 5.0
  78.  
  79. If you do not have the redirector included with the MS-DOS 5.0,
  80. obtain the redirector by ordering the Supplemental disks or
  81. by downloading the disks from the Microsoft Product Support
  82. Download Service (MSDL). For more information, see the coupon
  83. at the back of the MICROSOFT MS-DOS 6 USER'S GUIDE.
  84.  
  85. After you obtain the redirector, follow the instructions in the
  86. NET.TXT file on the Supplemental disks.
  87.  
  88. 5. Arcnet systems
  89. =================
  90. If your network uses Arcnet hardware, you might need to run the
  91. Microsoft Diagnostics (MSD) program by using the MSD /I command.
  92. If you must use the /I switch, do not choose the Networks option 
  93. in MSD.
  94.  
  95. 6. Artisoft LANtastic
  96. =====================
  97. If you are using any version of Artisoft LANtastic, 
  98. shut down the LANtastic server before you run MS-DOS 6
  99. Setup. There is no need to shut down the redirector.
  100.  
  101. Artisoft LANtastic versions 3.02 and higher are compatible 
  102. with MS-DOS 6.
  103.  
  104. If you are using a LANtastic version earlier than 2.5,
  105. contact your network vendor for an update.
  106.  
  107. If you are using LANtastic versions 2.5 through 3.01,
  108. carry out the following procedure
  109.  
  110. To update LANtastic versions 2.5 through 3.01:
  111.  
  112. 1. Shut down the LANtastic server. You can leave the
  113.    redirector running.
  114.  
  115. 2. Set up MS-DOS 6 on your computer. For more information
  116.    about installing MS-DOS 6, see the chapter 
  117.    "Getting Started" in the MICROSOFT MS-DOS USER'S GUIDE.
  118.  
  119.    If MS-DOS displays an "Incorrect DOS version" message
  120.    when your network restarts, ignore it.
  121.  
  122. 3. Type the following command at the command prompt:
  123.  
  124.    SETVER SERVER.EXE 4.00
  125.  
  126. 4. Restart your computer.
  127.  
  128. If you are using EMM386, you might need to exclude the
  129. memory area used by the network adapter card. To do this,
  130. use the X switch with the DEVICE command for EMM386.EXE in
  131. your CONFIG.SYS file. If you are using the factory-set
  132. defaults for the LANtastic 2Mbps adapter, include the 
  133. X=D800-DFFF switch with the DEVICE command for EMM386.EXE. 
  134. If this memory region is not excluded, you might experience 
  135. problems with programs that use expanded memory.
  136.  
  137. NOTE  Microsoft Defragmenter is incompatible with 
  138. LANtastic network software if the server service is loaded. 
  139. If only the redirector is loaded, Microsoft Defragmenter is 
  140. compatible with LANtastic network software.
  141.  
  142. NOTE  You cannot use DoubleSpace to compress a drive on a LANtastic server
  143. because all local drives are viewed as network drives. To compress 
  144. a drive, disable the server service by typing REM and space in front 
  145. of the server command in your AUTOEXEC.BAT file, and restarting the
  146. computer. Then run DoubleSpace to compress the drive. After you run 
  147. DoubleSpace, remove the REM command from your AUTOEXEC.BAT file.
  148.  
  149. After you compress a drive on a server, some DoubleSpace features--
  150. such as the LIST, CHKDSK, MOUNT, and UNMOUNT features--will not work
  151. correctly unless you stop the server service.
  152.  
  153. Also, the NET command will not display the drive configuration of
  154. your server correctly. For example, any drive an "Available for
  155. DoubleSpace" drive will not be displayed at all. Also, drive C,
  156. if it is compressed, may be incorrectly displayed as a physical
  157. drive. If your host drive uses a drive letter after an "Available
  158. for DoubleSpace" drive, you can make it inaccessible by using that
  159. drive letter when you connect to another server.
  160.  
  161. 7. AT&T StarGroup (non-LAN Manager) 
  162. ===================================
  163. If your network software is AT&T StarGroup, run MS-DOS 6 Setup.
  164. When Setup displays the "You have specified that your computer 
  165. is connected to a network" screen, choose Continue, and follow 
  166. the instructions on your screen. If you cannot run your network 
  167. software after running Setup, carry out the following procedure:
  168.  
  169. 1. Type the following commands at the command prompt:
  170.  
  171.    SETVER SETUP.EXE 4.00
  172.    SETVER ATTSTART.EXE 4.00
  173.  
  174. 2. Restart your computer.
  175.  
  176. 3. Use your StarGroup installation disks to remove the
  177.    existing network software from your computer.
  178.  
  179. 4. Reinstall StarGroup. When the StarGroup installation
  180.    prompts you to indicate which version of MS-DOS you are
  181.    using, choose MS-DOS version 4.0.
  182.  
  183. 8. Banyan VINES 
  184. ===============
  185. Banyan VINES versions 4.1 and higher are compatible with MS-DOS 
  186. 6. You can use Banyan VINES version 4.0x with MS-DOS 6 if you
  187. have the REDIRALL.EXE or REDIR4.EXE file in the BANYAN
  188. directory on your hard disk.
  189.  
  190. If neither file is on your hard disk, but you have the VINES
  191. installation disks that include one of these files, copy
  192. the file to the directory on your hard disk that contains
  193. your network files.
  194.  
  195. If the files are not on your hard disk or on the VINES
  196. installation disks, contact your network vendor.
  197.  
  198. If you have a VINES version earlier than 4.0, contact your
  199. network vendor for an update.
  200.  
  201. NOTE
  202. In some cases, Banyan VINES is incompatible with MemMaker. For
  203. example, if your network software loads multiple components
  204. into different UMB regions, MemMaker may not work correctly on
  205. your computer.
  206.  
  207. 9. DEC Pathworks and PCSA
  208. =========================
  209. If you have DEC PATHWORKS for DOS version 4.1,
  210. carry out the following procedure:
  211.  
  212. 1. If you are upgrading from MS-DOS version 3.3 or earlier,
  213.    update your redirector file, REDIR.EXE. Obtain
  214.    REDIR.400 from the PATHWORKS disks or system service,
  215.    rename it to REDIR.EXE, and place it in your DECNET
  216.    directory.
  217.  
  218. 2. Install MS-DOS 6 on your computer. For more information about 
  219.    installing MS-DOS 6, see the chapter "Getting Started" in
  220.    the MS-DOS 6 USER'S GUIDE.
  221.  
  222. Version 4.0 of PATHWORKS for DOS is compatible with MS-DOS
  223. 6. However, you must carry out the following procedure to 
  224. achieve this compatibility.
  225.  
  226. To update PATHWORKS version 4.0:
  227.  
  228. 1. If you are upgrading from MS-DOS version 3.3 or earlier,
  229.    update your redirector file, REDIR.EXE. Obtain REDIR.400 
  230.    from the PATHWORKS disks or system service, rename it to 
  231.    REDIR.EXE, and place it in your DECNET directory.
  232.  
  233. 2. Install MS-DOS 6 on your computer. For more information about 
  234.    installing MS-DOS 6, see the chapter "Getting Started"
  235.    in the MS-DOS 6 USER'S GUIDE.
  236.  
  237. 3. Restart your computer, but do not yet run STARTNET.BAT,
  238.    which starts the network.
  239.  
  240. 4. Type each of the following lines at the command prompt:
  241.  
  242.    SETVER USE.EXE 4.00
  243.  
  244.    SETVER MEMMAN.EXE 4.00
  245.  
  246.    SETVER LAD.EXE 4.00
  247.  
  248.    SETVER SHOW.EXE 4.00
  249.  
  250.    SETVER NETSETUP.EXE 4.00
  251.  
  252. 5. Restart your computer, and run STARTNET.BAT.
  253.  
  254. NOTE  If you upgrade to PATHWORKS 4.1 from PATHWORKS 4.0,
  255. you must disable the SETVER commands you typed in this
  256. procedure. To do this after you install PATHWORKS 4.1,
  257. type the same commands, but replace the 4.00 with /D in
  258. each command.
  259.  
  260. If you are using a version of PATHWORKS or PCSA earlier than
  261. 4.0, contact your network vendor for an update. Meanwhile,
  262. if you are using PATHWORKS or PCSA version 3.x, you can
  263. start using MS-DOS 6 by carrying out the following
  264. procedure.
  265.  
  266. NOTE  To get support for MS-DOS Task Swapper, use
  267. PATHWORKS for DOS version 4.1 or later.
  268.  
  269. To temporarily update PATHWORKS or PCSA version 3.x:
  270.  
  271. 1. If you are upgrading from MS-DOS version 3.3 or earlier,
  272.    update your redirector file, REDIR.EXE. Obtain REDIR.400 
  273.    from the PATHWORKS disks or system service, rename it to 
  274.    REDIR.EXE, and place it in your DECNET directory.
  275.  
  276. 2. Install MS-DOS 6 on your computer. For more information about 
  277.    installing MS-DOS 6, see the chapter "Getting Started" in the 
  278.    MICROSOFT MS-DOS USER'S GUIDE. If MS-DOS displays a series of 
  279.    "Incorrect DOS version" messages when your network restarts,
  280.    ignore these.
  281.  
  282. 3. Type all of the following commands at the command
  283.    prompt:
  284.  
  285.    SETVER USE.EXE 4.00
  286.    SETVER EMSLOAD.EXE 4.00
  287.    SETVER SCH.EXE 4.00
  288.    SETVER NETSETUP.EXE 4.00
  289.    SETVER NCP.EXE 4.00
  290.    SETVER DNNETHAT.EXE 4.00
  291.    SETVER LAD.EXE 4.00
  292.    SETVER DLL.EXE 4.00
  293.    SETVER MEMMAN.EXE 4.00
  294.    SETVER DNNETHLD.EXE 4.00
  295.    SETVER SHOW.EXE 4.00
  296.  
  297. 4. Restart your computer.
  298.  
  299. 10. IBM PC LAN
  300. ==============
  301. If you use IBM PC LAN 1.34 and have problems with
  302. applications that use record locking or file locking, you
  303. may need an updated REDIR50.EXE file included in ICO 3039.
  304. Contact IBM Support Channel.
  305.  
  306. IBM PC LAN Program Version 1.33 or Earlier
  307. ------------------------------------------
  308. To use MS-DOS 6 with IBM PC LAN Program (PCLP), you need
  309. one of the following:
  310.  
  311. o IBM PCLP version 1.34 installed.
  312.  
  313. o IBM PCLP version 1.3x that has been updated to version
  314.   1.34 by applying the appropriate IBM Corrective Service 
  315.   Disks. Contact IBM Product Support to obtain the software 
  316.   you need.
  317.  
  318. If you are running a PCLP version earlier than 1.30, contact
  319. IBM for the necessary software and instructions.
  320.  
  321. To update IBM PCLP versions 1.30 through 1.34:
  322.  
  323. 1. Skip to step 3 if you are upgrading from version 1.34.
  324.    Otherwise, install the necessary IBM PCLP software by 
  325.    following the instructions included with the Corrective 
  326.    Service Disk(s) you received from IBM.
  327.  
  328. 2. Restart your computer, and make sure the network starts.
  329.  
  330.    If the network doesn't start, quit this procedure and
  331.    contact IBM for help.
  332.  
  333. 3. Set up MS-DOS 6 on your computer. For more information
  334.    about installing MS-DOS 6, see the chapter "Getting 
  335.    Started" in the MICROSOFT MS-DOS 6 USER'S GUIDE.
  336.  
  337.    When Setup restarts your computer, the following message 
  338.    appears on your screen:
  339.  
  340.    Start PC LAN Program 1.3 (Y/N)?
  341.  
  342. 4. Type N, and press ENTER.
  343.  
  344. 5. Type the following at the command prompt:
  345.  
  346.    SETVER NET.COM /D
  347.  
  348. 6. Restart your computer.
  349.  
  350.    The following message appears on your screen:
  351.  
  352.    Start PC LAN Program 1.3 (Y/N)?
  353.  
  354. 7. Type Y, and press ENTER.
  355.  
  356.    NOTE  If, after setting up MS-DOS, your CONFIG.SYS file
  357.    contains a command for loading the IFSFUNC.EXE file, disable it 
  358.    by typing REM and a space in front of the command. Then save 
  359.    the file and restart your computer.
  360.  
  361.    NOTE  Microsoft Defragmenter program will not run on a PCLP
  362.    server.
  363.  
  364. 11. IBM DOS LAN Requester Version 1.30 or Earlier
  365. =================================================
  366. To use MS-DOS 6 with IBM DOS LAN Requester, you need one
  367. of the following:
  368.  
  369. o DOS LAN Requester files that are included with OS/2 LAN
  370.   Server version 1.30.1.
  371.  
  372. o DOS LAN Requester files that come with OS/2 LAN Server
  373.   version 1.30, which has had IBM Corrective Service
  374.   Diskette (CSD) 5015 applied to it.  Contact IBM Product
  375.   Support to obtain the software you need.
  376.  
  377. If you are running a DOS LAN Requester version earlier than
  378. 1.30, contact IBM for the necessary software and
  379. instructions.
  380.  
  381. To update IBM DOS LAN Requester version 1.30:
  382.  
  383. 1. Upgrade your DOS LAN Requester software to version
  384.    1.30.1 by following the instructions included with IBM
  385.    Corrective Service Disk 5015.
  386.  
  387. 2. Restart your computer, and make sure the network starts.
  388.  
  389.    If the network doesn't start, quit this procedure and
  390.    contact IBM for help.
  391.  
  392. 3. Set up MS-DOS 6 on your computer. For more information
  393.    about installing MS-DOS 6, see the chapter "Getting 
  394.    Started" in the MICROSOFT MS-DOS 6 USER'S GUIDE.
  395.  
  396.    When Setup restarts your computer, the following
  397.    message appears on your screen:
  398.  
  399.    Start DOS LAN Requester (Y/N)?
  400.  
  401. 4. Type N, and press ENTER.
  402.  
  403. 5. Type the following at the command prompt:
  404.  
  405.    SETVER NET.COM /D
  406.  
  407. 6. Restart your computer.
  408.  
  409.    The following message appears on your screen:
  410.  
  411.    Start DOS LAN Requester (Y/N)?
  412.  
  413. 7. Type Y, and press ENTER.
  414.  
  415.    NOTE  If, after setting up MS-DOS, your CONFIG.SYS file
  416.    has a command for loading the IFSFUNC.EXE file,
  417.    disable it by typing REM and a space in front
  418.    of the command. Then save the file and restart
  419.    your computer.
  420.  
  421. 12. Microsoft LAN Manager and 100-Percent Compatible
  422.     Networks
  423. ====================================================
  424. If you are running any version of Microsoft LAN Manager
  425. or a 100-Percent Compatible network, and Setup referred
  426. you to this file, obtain updated network files by
  427. ordering the Supplemental disks or by downloading the disks
  428. from the Microsoft Product Support Download Service (MSDL). For
  429. more information, see the coupon at the back of the MICROSOFT
  430. MS-DOS 6 USER'S GUIDE.
  431.  
  432. After you obtain the Supplemental disks, follow the instructions
  433. in the NET.TXT file on the Supplemental disks.
  434.  
  435. 13. Microsoft MS-Net and 100-Percent Compatible
  436.     Networks
  437. ===============================================
  438. If you are running any version of Microsoft MS-Net
  439. or a 100-Percent Compatible network, and Setup referred
  440. you to this file, obtain updated network files by
  441. ordering the Supplemental disks or by downloading the disks
  442. from the Microsoft Product Support Download Service (MSDL). For
  443. more information, see the coupon at the back of the MICROSOFT
  444. MS-DOS 6 USER'S GUIDE.
  445.  
  446. After you obtain the Supplemental disks, follow the instructions
  447. in the NET.TXT file on the Supplemental disks.
  448.  
  449. 14. Net/One PC
  450. ==============
  451. If Ungermann-Bass Net/One PC does not load with MS-DOS 6,
  452. do one of the following:
  453.                               
  454. o Contact your network vendor to get an updated LOADNIU.EXE file.
  455.  
  456. o Put a UBPAUSE command between the LOADNIU and XNSBIOS
  457.   lines in your MSNET.INI file.
  458.  
  459. o Run network commands from a batch file that includes a
  460.   PAUSE command between the LOADNIU and XNSBIOS lines.
  461.      
  462. 15. Novell Networks
  463. ===================
  464. When this NETWORKS.TXT file was published, the current version 
  465. of the workstation shell was 3.31. Obtain version 3.31 or later 
  466. for use with MS-DOS 6.
  467.  
  468. If you have a NetWare version earlier than 2.1, or your network
  469. software uses any of the following files, contact your network
  470. vendor:
  471.  
  472. NET3.COM
  473. NET4.COM
  474. XMSNET3.EXE
  475. XMSNET4.EXE
  476. EMSNET3.EXE
  477. EMSNET4.EXE
  478.  
  479. If you can't use Task Swapper in MS-DOS Shell when running
  480. a Novell network, contact your network vendor.
  481.  
  482. If you can't load MS-DOS 6 on your remote-boot workstation,
  483. contact Novell for the RPLFIX.COM file.
  484.  
  485. If you run LOGIN.EXE, MAP.EXE, and SESSION.EXE from MS-DOS
  486. Shell or while MS-DOS Shell is running, a search path is not
  487. added to the existing path. Use these programs before starting
  488. MS-DOS Shell.
  489.  
  490. If you use the Novell login program to set the COMSPEC
  491. variable after starting MS-DOS 6, and you can't
  492. reload the COMMAND.COM file, edit the SHELL command line
  493. in your CONFIG.SYS file. Make sure the path to
  494. COMMAND.COM points to the root directory and remove the
  495. C:\DOS\ parameter that follows the path, if one exists.
  496.  
  497. For example, suppose your SHELL command line looks like
  498. this:
  499.  
  500.     SHELL=C:\DOS\COMMAND.COM  C:\DOS\  /P  /E:512
  501.  
  502. Change it to look like this:
  503.  
  504.     SHELL=C:\COMMAND.COM  /P  /E:512
  505.  
  506. Or contact your Novell vendor to get a new login program.
  507.  
  508. If you are having problems using Microsoft Undelete on 
  509. a Novell network, use the MAP ROOT command in conjunction
  510. with the Delete Sentry level of delete protection. (If you have
  511. Novell Netware version 2.15c or older, obtain the most
  512. recent MAP.EXE file from your network vendor.) For example,
  513. you would use MAP ROOT syntax similar to the following (normally
  514. specified in the server's login script):
  515.  
  516. MAP ROOT F:=COUNT/SYS:USERS/JOEB
  517.  
  518. In this example, F is the network drive letter, COUNT is a file 
  519. server name, SYS is the volume name, USERS is a subdirectory of 
  520. volume SYS, and JOEB is the root for a network user. On JOEB's 
  521. computer, the AUTOEXEC.BAT file would contain the following syntax:
  522.  
  523. UNDELETE /SF
  524.  
  525. The /S switch specifies the Delete Sentry level of delete protection and 
  526. F specifies a network drive to be protected. The AUTOEXEC.BAT file should
  527. specify /S[drive] for each drive to be protected.
  528.  
  529. NOTE
  530. If you use Microsoft Backup for MS-DOS or Windows to back up files 
  531. to a network, and your network software is NetWare 286, the gas gauge 
  532. will move very slowly at first. This is due to the way NetWare 286 
  533. handles writing files to the network.
  534.  
  535. NOTE
  536. The %OS_VERSION parameter used in login scripts will return v5.00 if
  537. you are using any shell up to, and including, version 3.31. Until
  538. Novell releases an updated shell, refrain from using the %OS_VERSION 
  539. parameter or map a v6.00 drive over the existing v5.00 drive in a user's 
  540. login script.
  541.  
  542. MS-DOS Setup and Shared Windows Configuration
  543. ---------------------------------------------
  544. If you use a search drive to access your Windows initialization files
  545. (PROGMAN.INI, SYSTEM.INI, and WINFILE.INI) on a network directory, and
  546. you want to install the Windows programs included with MS-DOS 6,
  547. carry out the following procedure before you run Setup.
  548.  
  549. NOTE The information in this section applies both to the normal 
  550. Setup installation program and Setup run with the /E switch.
  551.  
  552. * Temporarily override the search drive by using the MAP command
  553.   at the command prompt. For example, if the network drive assignment
  554.   for your Windows directory is W, and the path is \USER\JOEB,
  555.   type MAP DEL W: at the command prompt to temporarily delete the
  556.   search drive. Then type MAP W:=SYS:USER\JOEB at the command prompt. 
  557.   Then run Setup. After Setup is finished and restarts your computer, 
  558.   your system will return to its normal configuration.
  559.  
  560. 16. Novell Networks and DoubleSpace
  561. ===================================
  562. If your network software is NetWare, make sure it is running before you 
  563. run DoubleSpace.
  564.  
  565. NetWare Lite
  566. ------------
  567. NetWare Lite uses all "Available for DoubleSpace" drives when the 
  568. network  software mounts remote file systems. As a result, MS-DOS displays 
  569. the "Not ready error" when you try to access the drives and Windows File 
  570. Manager shows the drives as floppy drives. In addition, if you
  571. attempt to compress another drive, DoubleSpace will not be able to
  572. use the former "Available for DoubleSpace" drives, even if you use
  573. the NET MAP DEL command.
  574.  
  575. To avoid drive conflicts, run DoubleSpace in Custom mode. Then specify
  576. for your host drive a letter that won't conflict with the drive letter
  577. your network software uses. For example, if your network drive is
  578. currently F, you could use E for your host drive when you
  579. install DoubleSpace.
  580.  
  581. 17. PC-NFS
  582. ==========
  583. If you use SETVER to report a different version of MS-DOS to
  584. a program, PC-NFS 3.x may report the version incorrectly. If 
  585. you are having this problem, contact your network vendor for 
  586. updated network software.
  587.  
  588. If you use PC-NFS 3.0 with MS-DOS Shell, MS-DOS Shell might
  589. display more drives than you have currently enabled. To
  590. prevent this, use the PC-NFS /D switch to specify the number
  591. of drives you are using. For more information, see your PC-
  592. NFS documentation.
  593.  
  594. If you can't use the COPY or XCOPY command on PC-NFS 3.01,
  595. contact your vendor to get an updated version of the
  596. PCNFS.SYS device driver.
  597.  
  598. If you use PC-NFS network software, carry out the following procedure
  599. before you run MemMaker:
  600.  
  601. 1. Open your MEMMAKER.INF file using any text editor. This file is
  602.    in the directory that contains your MS-DOS files.
  603.  
  604. 2. Add the following line to the file:
  605.  
  606.    *NET
  607.  
  608. 3. Save the file, and then run MemMaker.
  609.  
  610. 18. TCS 10Net or DCA 10Net 
  611. ==========================
  612. DCA 10Net Plus Versions 4.20 (20) and later, and DCA
  613. 10Net versions 3.3 (41) and later are compatible with
  614. MS-DOS 6. If you have an earlier version, contact
  615. your network vendor for an update.
  616.  
  617. If you are running a compatible version of 10Net Network 
  618. Software, disable the network software, and then run MS-DOS 6 
  619. Setup. After you install MS-DOS 6, reenable your network
  620. software.
  621.  
  622. NOTE
  623. Microsoft Defragmenter program is incompatible with 
  624. 10Net network software if the server service is loaded. 
  625. If only the redirector is loaded, the program is compatible
  626. with 10Net network software.
  627.  
  628. NOTE
  629. You cannot use DoubleSpace to compress a drive on a 10Net server
  630. because all local drives are viewed as network drives. To compress 
  631. a drive, disable the server service by typing REM and space in front 
  632. of the server command in your AUTOEXEC.BAT file, and restarting the
  633. computer. Then run DoubleSpace to compress the drive. After you run 
  634. DoubleSpace, remove the REM command from your AUTOEXEC.BAT file.
  635.  
  636. After you compress a drive on a server, some of DoubleSpace's features--
  637. such as the LIST, CHKDSK, MOUNT, and UNMOUNT features--will not work
  638. correctly unless you stop the server service.
  639.